1. Place the engine vertically. Remove the fixing screw of the cylinder head. Note that the screws should be loosened from both ends to the middle, and the screws should be removed three times. Lift the cylinder head, remove the cylinder cushion, and pay attention to the installation direction of the cylinder cushion. Loosen the oil release screw of the oil span shell and drain the oil in the oil span shell.
2. Disassembly of engine fuselage components 1) Remove the fixing screw of the cylinder head, note that the screw should be crossed and loosened from both ends to the middle, and the screw should be removed in 3 times. 2) Lift the cylinder head. Remove the cylinder pad and pay attention to the installation direction of the cylinder pad. Loosen the oil release screw of the oil span shell to release the oil in the oil span shell.
3. The steps for disassembly and disassembly of the engine are as follows: place the engine upright. Remove the intake and exhaust manifolds and the cylinder head outlet pipes. Remove the cylinder head cover. Remove the rocker arm assembly on the cylinder head, remove the boom chamber cover, remove the putter, and take out the boom in order. At the same time, write the sequence number. Remove the cylinder head and gasket.
4. Remove the clutch tie rod, separation fork and transmission shaft, remove the engine support rod and the front and rear support frame nuts; tie the engine with a rope;Hang it down with the engine hanger. Engine disassembly principle: from auxiliary parts to main parts, from the outside to the inside.
5. Engine disassembly steps and methods: Step 1: Remove the intake and exhaust pipes and exhaust pipes of the cylinder head. Step 2: Remove the valve cover. Remove the locking nut of the rocker arm shaft bracket and take out the rocker arm and shaft together. Remove all the putts. And make a good order so that the original friction pair can be maintained during installation.
6. The specific disassembly steps are as follows: Method 1: Unplug the battery wiring when the ignition switch is turned off. Take out the battery. Pay attention to pull it out first and then take it off. Unstighten the fastening bolt of the battery bracket and remove the battery bracket. Place a collection plate under the engine. Unscrew the lid of the coolant storage tank.
1. Hello: Release the oil first. Disassemble the exterior accessories. Remove the timing and cylinder head parts, remove the connecting rod and piston. Disassemble the crankshaft.
2. Disassembly steps: To remove the external components of the fuselage, first remove the external parts as required, and remove the motor, generator and other components. Then remove the intake and exhaust manifold, remove the cylinder cover, and then remove the gasoline pumps on both sides, so that the external components of the engine are basically dismantled.
3. Disassembly and installation steps of the car engine valve group Disassembly of the car engine valve group (1) Remove the valve adjustment gasket. (2) Remove the inlet and exhaust doors. Use valve disassembly pliers to compress the valve spring, and remove the lock, spring seat, valve spring and valve successively. (3) Use sharp-nosed pliers to remove the valve lever oil seal.
4. Engine disassembly steps: place the engine upright, remove the inlet and exhaust manifolds and the cylinder head outlet pipes. Remove the cylinder head cover, remove the rocker arm shaft assembly on the front and rear cylinder head; remove the crankshaft ventilation pipe, and remove the boom chamber cover; remove the putter.
1. Disassembly of engine body components 1) Remove the fixing screw of the cylinder head. Note that the screw should be crossed and loosened from both ends to the middle, and the screw should be removed three times. 2) Lift the cylinder head. Remove the cylinder pad and pay attention to the installation direction of the cylinder pad. Loosen the oil release screw of the oil span shell to release the oil in the oil span shell.
2. Engine disassembly steps and methods: Step 1: Remove the intake and exhaust pipes and exhaust pipes of the cylinder head. Step 2: Remove the valve cover. Remove the locking nut of the rocker arm shaft bracket and take out the rocker arm and shaft together. Remove all the putts. And make a good order so that the original friction pair can be maintained during installation. Step 3: Remove the timing gear cover and gasket camshaft.
3, 2 Turn the main switch to the "OFF" position. 3 Remove the outer cover of the car. 4 Dray the engine oil.5 Remove the negative wire of the battery first, and then remove the positive wire. 6 Remove the carburetor and automatically start the thickening valve wire. 7 Remove the starting motor wire from the starting relay, and unplug the spark plug cap and high-voltage wire.
4. Place the engine vertically. Remove the fixing screw of the cylinder head. Note that the screws should be loosened from both ends to the middle, and the screws should be removed three times. Lift the cylinder head, remove the cylinder cushion, and pay attention to the installation direction of the cylinder cushion. Loosen the oil release screw of the oil span shell and drain the oil in the oil span shell.
5. The disassembly of the engine is to put the engine removed from the frame on the workbench. 1: Place the engine upright, remove the inlet and exhaust manifolds and the cylinder head outlet pipes.
*Global supplier scorecard templates-APP, download it now, new users will receive a novice gift pack.
1. Place the engine vertically. Remove the fixing screw of the cylinder head. Note that the screws should be loosened from both ends to the middle, and the screws should be removed three times. Lift the cylinder head, remove the cylinder cushion, and pay attention to the installation direction of the cylinder cushion. Loosen the oil release screw of the oil span shell and drain the oil in the oil span shell.
2. Disassembly of engine fuselage components 1) Remove the fixing screw of the cylinder head, note that the screw should be crossed and loosened from both ends to the middle, and the screw should be removed in 3 times. 2) Lift the cylinder head. Remove the cylinder pad and pay attention to the installation direction of the cylinder pad. Loosen the oil release screw of the oil span shell to release the oil in the oil span shell.
3. The steps for disassembly and disassembly of the engine are as follows: place the engine upright. Remove the intake and exhaust manifolds and the cylinder head outlet pipes. Remove the cylinder head cover. Remove the rocker arm assembly on the cylinder head, remove the boom chamber cover, remove the putter, and take out the boom in order. At the same time, write the sequence number. Remove the cylinder head and gasket.
4. Remove the clutch tie rod, separation fork and transmission shaft, remove the engine support rod and the front and rear support frame nuts; tie the engine with a rope;Hang it down with the engine hanger. Engine disassembly principle: from auxiliary parts to main parts, from the outside to the inside.
5. Engine disassembly steps and methods: Step 1: Remove the intake and exhaust pipes and exhaust pipes of the cylinder head. Step 2: Remove the valve cover. Remove the locking nut of the rocker arm shaft bracket and take out the rocker arm and shaft together. Remove all the putts. And make a good order so that the original friction pair can be maintained during installation.
6. The specific disassembly steps are as follows: Method 1: Unplug the battery wiring when the ignition switch is turned off. Take out the battery. Pay attention to pull it out first and then take it off. Unstighten the fastening bolt of the battery bracket and remove the battery bracket. Place a collection plate under the engine. Unscrew the lid of the coolant storage tank.
1. Hello: Release the oil first. Disassemble the exterior accessories. Remove the timing and cylinder head parts, remove the connecting rod and piston. Disassemble the crankshaft.
2. Disassembly steps: To remove the external components of the fuselage, first remove the external parts as required, and remove the motor, generator and other components. Then remove the intake and exhaust manifold, remove the cylinder cover, and then remove the gasoline pumps on both sides, so that the external components of the engine are basically dismantled.
3. Disassembly and installation steps of the car engine valve group Disassembly of the car engine valve group (1) Remove the valve adjustment gasket. (2) Remove the inlet and exhaust doors. Use valve disassembly pliers to compress the valve spring, and remove the lock, spring seat, valve spring and valve successively. (3) Use sharp-nosed pliers to remove the valve lever oil seal.
4. Engine disassembly steps: place the engine upright, remove the inlet and exhaust manifolds and the cylinder head outlet pipes. Remove the cylinder head cover, remove the rocker arm shaft assembly on the front and rear cylinder head; remove the crankshaft ventilation pipe, and remove the boom chamber cover; remove the putter.
1. Disassembly of engine body components 1) Remove the fixing screw of the cylinder head. Note that the screw should be crossed and loosened from both ends to the middle, and the screw should be removed three times. 2) Lift the cylinder head. Remove the cylinder pad and pay attention to the installation direction of the cylinder pad. Loosen the oil release screw of the oil span shell to release the oil in the oil span shell.
2. Engine disassembly steps and methods: Step 1: Remove the intake and exhaust pipes and exhaust pipes of the cylinder head. Step 2: Remove the valve cover. Remove the locking nut of the rocker arm shaft bracket and take out the rocker arm and shaft together. Remove all the putts. And make a good order so that the original friction pair can be maintained during installation. Step 3: Remove the timing gear cover and gasket camshaft.
3, 2 Turn the main switch to the "OFF" position. 3 Remove the outer cover of the car. 4 Dray the engine oil.5 Remove the negative wire of the battery first, and then remove the positive wire. 6 Remove the carburetor and automatically start the thickening valve wire. 7 Remove the starting motor wire from the starting relay, and unplug the spark plug cap and high-voltage wire.
4. Place the engine vertically. Remove the fixing screw of the cylinder head. Note that the screws should be loosened from both ends to the middle, and the screws should be removed three times. Lift the cylinder head, remove the cylinder cushion, and pay attention to the installation direction of the cylinder cushion. Loosen the oil release screw of the oil span shell and drain the oil in the oil span shell.
5. The disassembly of the engine is to put the engine removed from the frame on the workbench. 1: Place the engine upright, remove the inlet and exhaust manifolds and the cylinder head outlet pipes.
*How to interpret complex trade patterns
author: 2024-12-23 21:39Trade data for logistics risk mitigation
author: 2024-12-23 21:02Global trade certificate verification
author: 2024-12-23 23:30HS code-based global benchmarking
author: 2024-12-23 23:03Marine exports HS code insights
author: 2024-12-23 22:07Meat and poultry HS code references
author: 2024-12-23 21:24133.95MB
Check681.17MB
Check893.82MB
Check973.83MB
Check512.71MB
Check328.37MB
Check452.52MB
Check518.52MB
Check245.67MB
Check637.97MB
Check991.39MB
Check338.17MB
Check317.38MB
Check258.34MB
Check254.99MB
Check546.93MB
Check825.82MB
Check663.96MB
Check656.46MB
Check484.79MB
Check814.22MB
Check865.75MB
Check918.49MB
Check771.49MB
Check889.85MB
Check864.45MB
Check987.62MB
Check892.91MB
Check263.26MB
Check264.12MB
Check773.44MB
Check817.12MB
Check512.91MB
Check567.85MB
Check225.43MB
Check369.37MB
CheckScan to install
Global supplier scorecard templates to discover more
Netizen comments More
1721 CIS countries HS code usage patterns
2024-12-23 23:10 recommend
1546 Trade compliance tools for exporters
2024-12-23 22:56 recommend
2987 Deriving product origin via HS code
2024-12-23 22:13 recommend
312 HS code-driven route selection
2024-12-23 21:48 recommend
2000 HS code verification in Middle Eastern markets
2024-12-23 21:45 recommend