Maritime insurance via HS code data

List of the contents of this article:

• 1,Maritime insurance via HS code data How to disassemble the leaf board
• 2. How to disassemble the red flag h5 roof?, It's better to have a video
• 3, How to disassemble the wiper of the car?

How to disassemble the leaf board video tutorial

First start the car to the right and drive the full wheel, then turn off the engine and pull out the car key, then open the hood and disconnect the negative pole of the battery. Remove the four screws on the front bumper with a Phillips screwdriver.

Remove the four screws on the front bumper with a Phillips screwdriver.Remove the two screws on the side of the front bumper, remove the three screws at the bottom right of the front bumper, and remove the three screws of the fender. Remove the fender. Remove the screws connecting the splash cover and the wing plate, and the wing plate can be removed.

Front leaf plate lining disassembly tutorial: use a movable socket wrench and a screwdriver to remove the pressure strip under the front windshield, and then remove the screws of the wing plate in order, and remove the leaf plate lining in 20 minutes.

Front leaf plate lining disassembly tutorial: use a movable socket wrench and a screwdriver to remove the adhesive strip under the front windshield first, and then remove the screws of the wing plate in order. The leaf plate lining will be removed in 20 minutes. If the iron plate is not thick, don't use an iron hammer, otherwise it will be counterproductive. Use a small rubber hammer cushion, otherwise the paint surface will be damaged.

SteamHow to disassemble the car leaf plate? The leaf plate (Fender), also known as the wing plate, refers to a kind of covering on motor vehicles and non-motor vehicles. To disassemble the leaf plate, the bumper must be removed, because the bumper has a fixing screw on the leaf plate. Leaf board is also called wing board. The position of the leaf plate is outside the body of the wheel.

How to disassemble the red flag h5 roof?, It's better to have a video

1. The sunroof of the vehicle needs to be opened so that there is better operating space when removing the roof. Above the rear seat of the vehicle, find the two screws connecting the roof and remove them with a screwdriver. Disassemble the front and rear headlights, remove the lampshade, remove the headlights with a screwdriver, and then pull out the headlight line.

2. Brother, I don't recommend disassembling the ceiling by individuals. Most of the ceilings are equipped with snaps or Velcro around the sky window, and screws, bolts or snaps are arranged in the front and rear. The probability of personal disassembly and folding is very high. ( Even for professionals, there is a high risk of disassembly, which is determined by the structure and material).

3. Open the hood of the Red Flag h5 engine and remove the engine decorative cover.When disassembling, use a screwdriver to pry up the upper latch and pry open the two upper latches. Then use a screwdriver to pry open the lower latch and pry open the two latches below.

4. Open the door, find the pressure strip on the roof, and gently pull the pressure strip with your hand to get it out of the fixed position of the roof. Remove the decorative panel or interior panel inside the roof in order to better remove the pressure bar. Pull out the pressure bar from the slot inside the roof, and be careful not to damage other parts inside the roof.

5. Gently pry it open along the gap of the trim panel with a small one-character cone to fix the removal of the screw on the right side of the sunroof switch. Now we can see the screws inside. First, remove the screw on the right, take out the t-20 sprene, and gently remove the screw with the t-20 sprene. The left side of the sunroof is the same.The first disassembly of the sunroof switch.

How to disassemble the wiper of the car?

First of all, we should prepare the special tools needed to disassemble the wiper. Then prepare the next disassembly operation process in advance. Open the engine cover of the vehicle, take out the screwdriver, and use the screwdriver to pry open the small black cover of the wiper. There is a small round hole on the edge of the small black cover. You can turn up the small round hole.

First of all, we need to prepare the tools needed to disassemble the wiper, a word change cone, a small-level wheel, a No. 13 sleeve, and then prepare for the next disassembly operation process.

The steps are as follows: First, stand up the wiper arm of the car at 90 degrees. Then grab the fixed wiper arm with one hand, and remove it with a little force with the other hand.

First of all, prepare the disassembly tools, a one-word cone, a small ratchet, and a No. 13 sleeve. Open the front cover of the car, take out the one-word change cone, and pry off the small black cover of the wiper with the one-word change cone. There is a small hole on the edge of the small black cover, which can be pryed open through this small hole.

How to disassemble and install the wiper? When installing the wiper, pay attention to the alignment of the raised part on the bracket with the card slot to avoid excessive force causing damage to the card slot. At the same time, when replacing the wiper, pay attention to choosing a wiper that matches the size of the original car to ensure the effect and safety of use.