Premium trade data intelligence subscriptions

List of Contents of this article:

• 1, Does DCS include FSSS?
• 2, What is the function of PLC?
• 3 、How to control the frequency converter with analog quantity
• 4,Premium trade data intelligence subscriptions What is DCS control
• 5, What is DCS? What is CEMS? What is FGD?
• 6, dd C control system principle

Does DCS include FSSS?

1. The main manufacturers of the distribution control system (DCS) are Westinghouse (Emerson), Hitachi, ABB, GE (Xinhua), and Lihua, Guodian Zhishen, etc. These systems integrate FSSS, DEH, EH, TSI, CSS, etc. In addition, the control of the desulfurization system is separate.

2. Machine protection is mainly done by ETS and DEH actions. Downtime is divided into ETS downtime and DEH downtime. Furnace protection is achieved through FSSS, which is part of the function of DCS. There is a FSSS relay cabinet, and the relay can be sucked. Haha. This question should be for beginners in thermal engineering..

3. DCS, that is, the distributed control system, is composed of process control level and process monitoring level for communication.The network is a multi-level computer system that integrates 4C technologies such as computer, communication, display and control.

4. DCS includes a lot of content: analog control system (MCS), sequential control system (SCS), engine DEH system, electrical ECS system, bypass control system BCS system.

5. The above is an introduction to the boiler MFT. The description of the boiler large interlock, FSSS, and other equipment is limited to the length and will not be introduced one by one. One thing is very important, the temperature and pressure compensation of the steam flow rate and the temperature and pressure compensation of the steam package level. In order to measure the accurate steam flow rate and the steam package level, the temperature and pressure compensation must be carried out.

What is the function of PLC?

Modern PLC has mathematical operations (including matrix operations, function operations, logical operations), data transmission, data conversion, sorting, table checking, bit operation and other functions, which can complete the collection, analysis and processing of data.

Programmable Logic Controller (PLC), a digital electronic device with a microprocessor, is a digital logic controller for automated control, which can load control instructions into memory storage at any time. Deposit and execute.

PLC can collect analog signals, digital signals and pulse signals. ( 3) Output control function. It can output digital signals, analog signals and pulse signals to control external solenoid valves, indicator lights and other equipment. ( 4) Data processing function.

The purpose of PLC is to control the switching quantity. The ability of PLC to control the switching quantity is very strong.

How does Mitsubishi plc use analog to control the frequency converter

As long as 2DA That's it. Write a 2DA program, and the numbersThe quantity is output to the specified channel, and the analog quantity is output to the frequency converter. The frequency converter can select the terminal control.

The method of Mitsubishi pic controlling the frequency converter is as follows. The switching signal of the PLC is used to control the output point and COM point of the frequency converter PLC (MR type or MT type) directly with the STF (positive start), RH (high speed), RM (medium speed), RL (low speed) and input terminal of the frequency converter. SG and other ports are connected separately.

You can output a voltage of 0-10V with the analog output module, and then connect this 0-10V voltage to the input device of the frequency converter. The frequency converter outputs the frequency of 0-50HZ according to the voltage of 0-10V, so as to adjust the speed of the motor. You can also Forum or China Industrial Control Forum to find moreDetailed

Use the analog output module of the PLC to control the analog output module of the frequency converter PLC to output 0 to 5V voltage signal or 4 to 20mA current signal, as the analog input signal of the frequency converter to control the output frequency of the frequency converter.

Mitsubishi inverter analog signal: The analog signal required to control the Mitsubishi inverter can be 0-5V, 0-10V, 4-20mA, etc. These signals can be used either with the output analog signal of the Mitsubishi inverter, or can be given through external signals (such as through PLC module The implementation of the simulated output module).

First of all, the first step is to open the front cover of the frequency converter, and then connect the main loop of the frequency converter. Then it is necessary to input three-phase AC 380V: L1;L2; L3, the output is three-phase U; V; W. Then it is necessary to connect the motor with a 0.5 square wire.

What is DCS control

1. DCS is the English abbreviation of Distributed Control System, and the distributed control system is abbreviated as DCS, which can also be directly It is translated as "distributed control system" or "distributed computer control system".

2. DCS is the English abbreviation of Distributed Control System, which is also known as Distributed Control System in the domestic automatic control industry. It is a new type of computer control system relative to the centralized control system. It is developed and evolved on the basis of the centralized control system.

3. Overview: DCS is the English abbreviation of Distributed Control System, which is also known as distributed control system in the domestic automatic control industry. It is a new type of computer control system relative to the centralized control system. It is developed and evolved on the basis of the centralized control system.

4. DCS is the English abbreviation of Distributed Control System, which is also known as distributed control system in the domestic automatic control industry.

5. Definition of dcs control system: Based on multiple microprocessors, the control system designed with distributed control functions, centralized display operation, and taking into account the principles of autonomy and comprehensive coordination is called distributed control system (DCS).

6. What does dcs control system mean? The dcs control system means a distributed control system, also known as the distributed control system. Based on the microprocessor, it adopts a new generation of instrument control system with the design principles of distributed control functions, centralized display operation, and taking into account the design principles of autonomy and comprehensive coordination.

What is DCS? What is CEMS? What is FGD?

1. DCS is the English abbreviation of Distributed Control System, which is also known as Distributed Control System in the domestic automatic control industry. CEM: Electronics Manufacturing Services Provider.EMS. Professional contract factory. Professional electronic manufacturing services.

2. CEMS is for the environmental protection department, and DCS is a control system used for desulfurization and denitrification to produce gypsum. FGD is a flue gas desulfurization device or process, which is a whole.

3. FGD is an indispensable facility for chimneys to become thermal power plants. In recent years, with the application of desulfurization and denitrification technology, the temperature and flue gas composition after treatment have changed compared with the past.

ddc control system principle

A multi-functional digital control system that uses the time-sharing processing function of the computer to directly control multiple control loops in various forms. In this kind of system, the output of the computer directly acts on the control object, so it is called direct digital control, abbreviated as DDC.

DDC controller is the core of the whole control system and the key component for the system to realize the control function.

PLC and its related peripherals should be designed according to the principle that it is easy to form a whole with the industrial control system and expand its functions.