The neutral point is not grounded or through the arc Circle grounding system, occur singleWhen the grounding fails, because it does not constitute a short-circuit loop, the grounding short-circuit current is much smaller than the load current. This system is called a small-current grounding system.
Single-phase grounding of the power system refers to the grounding of one of the three phase lines of the power line, which is a fault phenomenon. The small grounding current system is a wiring mode and operation mode of the power system. It generally refers to the neutral point non-grounding system and the neutral point through-arc coil grounding system.
The so-called power supply "small grounding current system" is actually a branch of the power supply neutral point ungrounded system. It is grounded through a high resistance (or equivalent high resistance) at the neutral point of the power supply.
1. High-current grounding and small-current grounding are grounded by neutral points in the power system, which are distinguished according to the main operating characteristics. The small grounding current system is also known as the ineffective grounding system. Including neutral point non-grounding, extinguishing arc coil grounding, and high-impedance grounding system.
2. When a single-phase grounding fault occurs in a neutral point direct grounding system (including a system grounded by a small impedance), the grounding short-circuit current is very large, so this system is called a high-current grounding system.It adopts a system that is not grounded at the neutral point or grounded by an arc coil.
3. The so-called power supply "small grounding current system" is actually a branch of the power supply neutral point ungrounded system. It is grounded through a high resistance (or equivalent high resistance) at the neutral point of the power supply.
4. For 10kV systems, there are common ungrounded systems, mainly because the capacitor current is relatively small, and the damage to the equipment is relatively small when single-phase grounding occurs. It can operate with faults and provide maintenance time for maintenance personnel. The speed of finding faults can be improved by equipping a small-current wire selector.
The characteristic of a small grounding current is that when a phase grounding fault occurs, the grounding current is limited to a smaller value, and the ground steady-state voltage of the non-fault phase may reach the line voltage. The large grounding current system is also known as the effective grounding system. Including neutral point direct grounding and low-impedance grounding systems.
In the non-grounded system of the neutral point, when the insulation of any phase is destroyed and grounded, the line voltage between the phases remains unchanged, and it can continue to operate with faults, and the ground voltage and the ground capacitance current of each item change, and the point of the neutral point is far from the earth potential.
The neutral point is not grounded, and the earth and the system are not electrically connected.
When one-phase grounding occurs in a small-current grounding system, the grounding relative voltage is zero, and the other two relative ground voltages increase by three times.The magnitude of the grounding current at the contact point is equal to the sum of the grounding capacitance current of all lines.
When a single-phase metallic grounding occurs in a small current grounding system, the ground relative voltage is zero, and the non-ground relative ground voltage rises to line voltage.
Small grounding current grounding (i.e. ineffective grounding) includes: neutral point non-grounding, high resistance grounding, extinguishing arc coil grounding method, etc. When a single-phase grounding fault occurs in a small-current grounding system, because the neutral point is not effectively grounded, the fault point will not produce a large short-circuit current, so the system is allowed to operate with faults for a short time.
HS code application in re-export scenarios-APP, download it now, new users will receive a novice gift pack.
The neutral point is not grounded or through the arc Circle grounding system, occur singleWhen the grounding fails, because it does not constitute a short-circuit loop, the grounding short-circuit current is much smaller than the load current. This system is called a small-current grounding system.
Single-phase grounding of the power system refers to the grounding of one of the three phase lines of the power line, which is a fault phenomenon. The small grounding current system is a wiring mode and operation mode of the power system. It generally refers to the neutral point non-grounding system and the neutral point through-arc coil grounding system.
The so-called power supply "small grounding current system" is actually a branch of the power supply neutral point ungrounded system. It is grounded through a high resistance (or equivalent high resistance) at the neutral point of the power supply.
1. High-current grounding and small-current grounding are grounded by neutral points in the power system, which are distinguished according to the main operating characteristics. The small grounding current system is also known as the ineffective grounding system. Including neutral point non-grounding, extinguishing arc coil grounding, and high-impedance grounding system.
2. When a single-phase grounding fault occurs in a neutral point direct grounding system (including a system grounded by a small impedance), the grounding short-circuit current is very large, so this system is called a high-current grounding system.It adopts a system that is not grounded at the neutral point or grounded by an arc coil.
3. The so-called power supply "small grounding current system" is actually a branch of the power supply neutral point ungrounded system. It is grounded through a high resistance (or equivalent high resistance) at the neutral point of the power supply.
4. For 10kV systems, there are common ungrounded systems, mainly because the capacitor current is relatively small, and the damage to the equipment is relatively small when single-phase grounding occurs. It can operate with faults and provide maintenance time for maintenance personnel. The speed of finding faults can be improved by equipping a small-current wire selector.
The characteristic of a small grounding current is that when a phase grounding fault occurs, the grounding current is limited to a smaller value, and the ground steady-state voltage of the non-fault phase may reach the line voltage. The large grounding current system is also known as the effective grounding system. Including neutral point direct grounding and low-impedance grounding systems.
In the non-grounded system of the neutral point, when the insulation of any phase is destroyed and grounded, the line voltage between the phases remains unchanged, and it can continue to operate with faults, and the ground voltage and the ground capacitance current of each item change, and the point of the neutral point is far from the earth potential.
The neutral point is not grounded, and the earth and the system are not electrically connected.
When one-phase grounding occurs in a small-current grounding system, the grounding relative voltage is zero, and the other two relative ground voltages increase by three times.The magnitude of the grounding current at the contact point is equal to the sum of the grounding capacitance current of all lines.
When a single-phase metallic grounding occurs in a small current grounding system, the ground relative voltage is zero, and the non-ground relative ground voltage rises to line voltage.
Small grounding current grounding (i.e. ineffective grounding) includes: neutral point non-grounding, high resistance grounding, extinguishing arc coil grounding method, etc. When a single-phase grounding fault occurs in a small-current grounding system, because the neutral point is not effectively grounded, the fault point will not produce a large short-circuit current, so the system is allowed to operate with faults for a short time.
HS code lookup for Asia-Pacific markets
author: 2024-12-23 23:30HS code strategies for trade diversification
author: 2024-12-23 22:40How to meet import health standards
author: 2024-12-23 22:21Top international trade research methods
author: 2024-12-23 21:31Medical devices HS code mapping
author: 2024-12-23 21:18HS code-based multi-country consolidation
author: 2024-12-23 23:28End-to-end supplier lifecycle management
author: 2024-12-23 23:16Fisheries products HS code classification
author: 2024-12-23 21:12HS code-driven cost-benefit analyses
author: 2024-12-23 20:59941.59MB
Check631.42MB
Check157.66MB
Check276.31MB
Check221.11MB
Check526.86MB
Check351.11MB
Check865.17MB
Check363.69MB
Check325.45MB
Check972.54MB
Check795.54MB
Check337.76MB
Check946.62MB
Check222.42MB
Check145.29MB
Check918.44MB
Check285.19MB
Check462.76MB
Check353.21MB
Check178.95MB
Check723.62MB
Check532.39MB
Check789.66MB
Check472.89MB
Check424.93MB
Check744.51MB
Check681.96MB
Check736.16MB
Check754.82MB
Check771.49MB
Check171.64MB
Check942.49MB
Check938.71MB
Check697.16MB
Check539.34MB
CheckScan to install
HS code application in re-export scenarios to discover more
Netizen comments More
1706 Surgical instruments HS code classification
2024-12-23 22:49 recommend
2147 Predictive analytics for supplier risks
2024-12-23 22:23 recommend
1930 Global trade data warehousing solutions
2024-12-23 21:51 recommend
2398 Asia trade corridors HS code mapping
2024-12-23 21:43 recommend
609 HS code-based customs broker selection
2024-12-23 21:25 recommend