HS code for artisanal goods

List of the table of contents of this article:

• 1, What is the solution to solve
• 2, Some car throttles have two pull wires. What is their function?
• 3、What is the function of car throttle pulling the wire
• 4, How to adjust the throttle cable appropriately?
• 5, How to change the wire of the car windscreen

What is the solution to solve the problem of the car's gear pulling wire is frozen

After finding that the gearshift wire is frozen, you can light the car first. Start_, and then use the heat energy caused by the idling operation of the engine to unfreeze the gear shifting line. This method is also the easiest way to defrost.

Then if the brake disc freezes due to water inlet, you can only decide the solution by pouring hot water. After all, the degree of freezing is unknown, and the torque of the automatic transmission car at the moment of lifting the brake is not adjusted by the driver to a certain extent. Naturally, it is not recommended to defrost in an active way.

First of all, you need to start the motor vehicle and use the temperature of the engine to open the gear line. This solution is relatively simple and convenient. At least the engine needs to idle for more than 20 minutes, and then try to change the gear to drive the vehicle.

The method of defrosting the car gear line is: use the heat generated by the idling speed of the car engine to transfer to the position of the car's gear line, and the car gear line can be thawed. The temperature is very low in winter. After a night of parking, the vehicleThe viscosity of oil increases. If the cold car starts immediately, it will cause great damage to vehicle wear, so it is more important to heat the car in winter.

The solution to the freezing of the gearshift cable After finding that the gearshift cable is frozen, you can start the car first, and then use the heat generated when the engine is idle to thaw the gearshift cable. This method is also the simplest defrosting method.

Some car throttles have two pull wires. What is their function?

1. One is the throttle wire, and the other is the wiring to the automatic transmission, which plays a speed-up role. When the trottle is big, this pull wire works to control the gear shift. There is also a possibility that this pull wire works for cruise control.

2. [Pacific Automobile Network] The function of car throttle wire pulling is to control the throttle more directly and quickly, and the throttle response is faster and more timely. The wire-pulling throttle is that one end of the cable is connected to the throttle pedal, and the other end is connected to the throttle after passing through the fulcrum and guide. When stepping on the accelerator pedal, the throttle opens The angle of response.

3. Another function is to prevent the amount of throttle frame, which greatly affects the driver's perception of the throttle in the race.

4. If it is a double-wire right-hand throttle handle, there are two throttle lines under the cover. The accuracy of controlling the trottle is different: the double trottle line is more accurate than the single line trottle control. The throttle return effect is different: the double throttle line is better than the single throttle return.

5. Double throttle wire: one works when refueling, and the other works when returning the throttle, so as to avoid the carburetor not returning to position at the return throttle, causing danger to the high-speed engine.

What is the function of the car throttle pull line

One is the throttle line of the engine. The throttle pedal pulls the engine throttle line to control the opening size of the throttle valve, and then control the speed of the engine.

And the electronic throttle is controlled by cables or wire harnesses.On the surface, the opening of the throttle valve replaces the traditional throttle wire with a cable, but in essence, it is not just a simple change of the connection method, but also can realize the automatic control function of the power output of the whole vehicle.

What you are talking about is that the very old automatic transmission relies on the throttle pull to control the valve body to change the gear shift timing. The gear shift timing of the automatic transmission is related to the engine load. The greater the load, the later the gear shift timing. The position of the throttle and the engine speed can reflect the size of the load, so the automatic transmission at that time The position of the pulling line needs to be adjusted.

How to adjust the throttle cable properly?

1. You can try not to adjust the amplitude too much each time. After adjusting, check the deflection of the steel wire. It is best to control it within the appropriate range. Adjusting too tightly may increase the idle speed.

2. Key points for adjusting the gap of the pull line: rotate the adjustment nut clockwise, and tighten the pull line. When you feel that the smell gap has returned to the state before the failure, it is considered that the pulling force is appropriate.

3. The throttle line is in the lower part of the motorcycle body. While rotating the accelerator, you can see that there is a line shaking below. You can unscrew the screw there to relax it. If not, rotate the adjustment screw in front of the right handle. The specific operation is as follows: First, rotate the motorcycle to the accelerator and feel the tightness.

4. The throttle line is too tight. The adjustment method is to apply a little butter on it, and then step on it a few more times. There are many reasons why the throttle line is tight. In most cases, there are only two: the accelerator pedal is not well adjusted, and the bottom of the pedal has the function of adjusting the pedal area, which can be adjusted according to your own habits.

How to change the wire

1. First of all, let's find the right position to pass the wire. Then we put the ring on the head of the wire rope in first. At this time, we put the cylindrical part of the plastic card on the wire rope sheath on the card holder. Press hard and don't let go, and then we start to rotate the card.

2. Find the connection and plug-in parts at both ends of the wire and replace the wiring directly. However, the replacement of this connection line on the car is generally troublesome. Some structural parts such as decorative panels may need to be removed in the middle, and a little carelessness in the disassembly process may cause more trouble.

3. Easy to change, remove the glove box,Just remove the switch panel. There is a switch in it. There is a pull wire on Taobao. The key is that it will still break if it is replaced. It will be broken as soon as it is pulled, which is meaningless.

4. When the hood of the 5261 car is broken, the broken wire should be removed first. Equip a new pull wire and put the new pull wire in. The method of replacing the old wire with a new special line is to tangle the two wires together and stwew them together, and then pull out the other end to pull the new wire in.